1/7 ? z01 series standard 1a triac s october 2001 - ed: 4 main features: description the z01 series is suitable for general purpose ac switching applications. they can be found in applications such as home appliances (electrovalve, pump, door lock, small lamp control), fan speed controllers,... different gate current sensitivities are available, allowing optimized performances when controlled directly from microcontrollers. symbol value unit i t(rms) 1a v drm /v rrm 600 to 800 v i gt (q 1 ) 3 to 25 ma absolute maximum ratings symbol parameter value unit i t(rms) rms on-state current (full sine wave) sot-223 ttab = 90c 1 a to-92 ti = 50c i tsm non repetitive surge peak on-state current (full cycle, tj initial = 25c) f = 50 hz t = 20 ms 8 a f = 60 hz t = 16.7 ms 8.5 i 2 ti 2 t value for fusing tp = 10 ms 0.35 a 2 s di/dt critical rate of rise of on-state current i g = 2 x i gt , tr 100 ns f = 120 hz tj = 125c 20 a/s i gm peak gate current tp = 20 s tj = 125c 1 a p g(av) average gate power dissipation tj = 125c 0.1 w t stg t j storage junction temperature range operating junction temperature range - 40 to + 150 - 40 to + 125 c g a2 a1 a2 a1 a2 g a2 a1 to-92 (z01xxa) sot-223 (z01xxn)
z01 series 2/7 electrical characteristics (tj = 25c, unless otherwise specified) static characteristics note 1: minimum igt is guaranted at 5% of igt max. note 2: for both polarities of a2 referenced to a1 thermal resistances s = copper surface under tab symbol test conditions quadrant z01xx unit 03 07 09 10 i gt (1) v d = 12 v r l = 30 w i - ii - iii iv max. 3 5 5 7 10 10 25 25 ma v gt all max. 1.3 v v gd v d = v drm r l = 3.3 k w tj = 125c all min. 0.2 v i h (2) i t = 50 ma max. 7 10 10 25 ma i l i g = 1.2 i gt i - iii - iv max. 7 10 15 25 ma ii 15 20 25 50 dv/dt (2) v d = 67 %v drm gate open tj = 110c min. 10 20 50 100 v/s (dv/dt)c (2) (di/dt)c = 0.44 a/ms tj = 110c min. 0.5 1 2 5 v/s symbol test conditions value unit v tm (2) i tm = 1.4 a tp = 380 s tj = 25c max. 1.6 v v to (2) threshold voltage tj = 125c max. 0.95 v r d (2) dynamic resistance tj = 125c max. 400 m w i drm i rrm v drm = v rrm tj = 25c max. 5a tj = 125c 0.5 ma symbol parameter value unit r th(j-t) junction to tab (ac) sot-223 25 c/w r th(j-l) junction to lead (ac) to-92 60 r th(j-a) junction to ambient s = 5 cm 2 sot-223 60 c/w to-92 150
z01 series 3/7 product selector ordering information part number voltage sensitivity type package 600 v 700 v 800 v Z0103ma x 3 ma standard to-92 Z0103mn x 3 ma standard sot-223 Z0103sa x 3 ma standard to-92 Z0103sn x 3 ma standard sot-223 Z0103na x 3 ma standard to-92 Z0103nn x 3 ma standard sot-223 Z0107ma x 5 ma standard to-92 Z0107mn x 5 ma standard sot-223 Z0107sa x 5 ma standard to-92 Z0107sn x 5 ma standard sot-223 Z0107na x 5 ma standard to-92 Z0107nn x 5 ma standard sot-223 Z0109ma x 10 ma standard to-92 Z0109mn x 10 ma standard sot-223 Z0109sa x 10 ma standard to-92 Z0109sn x 10 ma standard sot-223 Z0109na x 10 ma standard to-92 Z0109nn x 10 ma standard sot-223 z0110ma x 25 ma standard to-92 z0110mn x 25 ma standard sot-223 z0110sa x 25 ma standard to-92 z0110sn x 25 ma standard sot-223 z0110na x 25 ma standard to-92 z0110nn x 25 ma standard sot-223 z 01 03 m a 1aa2 triac series current: 1a sensitivity: 03: 3ma 07: 5ma 09: 10ma 10: 25ma voltage: m: 600v s: 700v n: 800v package: a: to-92 n: sot-223 packing mode: 1aa2: to-92 bulk (preferred) 2al2: to-92 ammopack 5aa4: sot-223 tape & reel blank
z01 series 4/7 other information note: xx = sensitivity, y = voltage part number marking weight base quantity packing mode z01xxya 1aa2 z01xxya 0.2 g 2500 bulk z01xxya 2al2 z01xxya 0.2 g 2000 ammopack Z0103yn 5aa4 z3y 0.12 g 1000 tape & reel Z0107yn 5aa4 z7y 0.12 g 1000 tape & reel Z0109yn 5aa4 z9y 0.12 g 1000 tape & reel z0110yn 5aa4 z0y 0.12 g 1000 tape & reel fig. 1: maximum power dissipation versus rms on-state current (full cycle). fig. 2-1: rms on-state current versus ambient temperature (full cycle). fig. 2-2: rms on-state current versus ambient temperature (full cycle). fig. 3: relative variation of thermal impedance junction to ambient versus pulse duration. 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 0.00 0.25 0.50 0.75 1.00 1.25 1.50 p(w) it(rms)(a) 0 25 50 75 100 125 0.0 0.2 0.4 0.6 0.8 1.0 1.2 tl or ttab (c) it(rms)(a) sot-223 (rth(j-a)=rth(j-t)) to-92 (rth(j-a=rth(j-l)) 0 25 50 75 100 125 0.0 0.2 0.4 0.6 0.8 1.0 1.2 tamb(c) it(rms)(a) to-92 rth(j-a)=150c/w sot-223 (rth(j-a)=60c/w) 1e-3 1e-2 1e-1 1e+0 1e+1 1e+2 5e+2 0.01 0.10 1.00 k=[zth(j-a)/rth(j-a)] z01xxxn z01xxxa tp(s)
z01 series 5/7 fig. 4: relative variation of gate trigger current, holding current and latching current versus junction temperature (typical values). fig. 5: surge peak on-state current versus number of cycles. fig. 6: non-repetitive surge peak on-state current for a sinusoidal pulse with width tp < 10ms, and corresponding value of i2t. fig. 7: on-state characteristics (maximum values). fig. 8: relative variation of critical rate of decrease of main current versus (dv/dt)c (typical values). fig. 9: relative variation of critical rate of decrease of main current versus junction temperature. -40 -20 0 20 40 60 80 100 120 140 0.0 0.5 1.0 1.5 2.0 2.5 tj(c) igt,ih,il [tj] / igt,ih,il [tj=25c] igt ih & il 1 10 100 1000 0 1 2 3 4 5 6 7 8 9 itsm(a) non repetitive tj initial=25c repetitive tamb=25c one cycle t=20ms number of cycles 0.01 0.10 1.00 10.00 0.1 1.0 10.0 100.0 tp (ms) itsm (a), i2t (a2s) tj initial=25c itsm i2t di/dt limitation: 20a/s 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 0.1 1.0 10.0 itm(a) tj=25c tj max. vto= 0.95 v rd= 420 m w tj=tj max. vtm(v) 0.1 1.0 10.0 100.0 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 (di/dt)c [(dv/dt)c] / specified (di/dt)c Z0103 Z0107 z0110 Z0109 (dv/dt)c (v/s) 0 25 50 75 100 125 0 1 2 3 4 5 6 (di/dt)c [tj] / (di/dt)c [tj specified] tj (c)
z01 series 6/7 fig. 10: sot-223 thermal resistance junction to ambient versus copper surface under tab (printed circuit board fr4, copper thickness: 35 m m). 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 0 10 20 30 40 50 60 70 80 90 100 110 120 130 rth(j-a) (c/w) sot-223 s(cm2) package mechanical data sot-223 (plastic) ref. dimensions millimeters inches min. typ. max. min. typ. max. a 1.80 0.071 a1 0.02 0.1 0.0008 0.004 b 0.60 0.70 0.85 0.024 0.027 0.034 b1 2.90 3.00 3.15 0.114 0.118 0.124 c 0.24 0.26 0.35 0.009 0.010 0.014 d 6.30 6.50 6.70 0.248 0.256 0.264 e 2.3 0.090 e1 4.6 0.181 e 3.30 3.50 3.70 0.130 0.138 0.146 h 6.70 7.00 7.30 0.264 0.276 0.287 v 10 max a a1 b e1 d b1 h e e c v
z01 series 7/7 information furnished is believed to be accurate and reliable. however, stmicroelectronics assumes no responsibility for the co nsequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of stmicroelectronics. specifications mentioned in this publicati on are subject to change without notice. this publication supersedes and replaces all information previously supplied. stmicroelectronics prod ucts are not authorized for use as critical components in life support devices or systems without express written approval of stmicroelectro nics. ? the st logo is a registered trademark of stmicroelectronics ? 2001 stmicroelectronics - printed in italy - all rights reserved stmicroelectronics group of companies australia - brazil - china - finland - france - germany - hong kong - india - italy - japan - malaysia malta - morocco - singapore - spain - sweden - switzerland - united kingdom - u.s.a http://www.st.com package mechanical data to-92 (plastic) ref. dimensions millimeters inches min. typ. max. min. typ. max. a 1.35 0.053 b 4.70 0.185 c 2.54 0.100 d 4.40 0.173 e 12.70 0.500 f 3.70 0.146 a 0.45 0.017 d f a e b a c footprint dimensions (in millimeters) sot-223 (plastic)
|
